Open-plan living and dining — 119 m² flat

Sofa, coffee tables, dining table and chairs set as one scheme in a single open room, so the seating and dining zones read together from the entrance.

Client name withheld at the client’s request. Photographs are from the flat.

At a glance

SegmentResidential apartment
ScopeLiving and dining in one open room
SuppliedSofa, coffee tables, dining table and chairs
CustomisationSofa length set to the wall run; upholstery to the palette
Inspection100% of units before packing
Living zone looking through to the dining table in the open-plan flat
Living zone looking through to the dining table — one room, two zones

The brief

A 119 m² apartment had one long room for both living and dining. The client wanted the seating to hold the long wall and the dining table to sit close enough to be used, without the two zones crowding the walkway between them.

What shaped the layout

  • The long wall. It is the only uninterrupted run in the room, so the sofa had to sit there and set the length of the seating zone.
  • The window end. The table needed the daylight, but it could not block the kitchen island standing behind it.
  • The walkway. The gap between the sofa back and the chair backs had to stay clear enough to cross the room carrying something.
  • The palette. Red lacquer, a black lacquered floor and two large art panels were already fixed. The furniture had to sit inside those colours, not compete with them.
Kitchen dining island with red stools and brass pendant lights
Dining island — red stools and pendant lighting

Where the risk was

One room, two zones

In an open plan the sofa and the dining table are seen together. A sofa that is too tall or too deep makes the dining side look squeezed, even when both pieces are correct on their own.

The walkway comes first

The gap between the sofa back and the dining chairs decides whether the room works. If it is set from a catalogue, the result is a room that photographs well and is awkward to walk through.

Palette across suppliers

Seating came from our workshop; tables and chairs from partner workshops. Two wood tones that looked close in isolation read as a mismatch under the same window light.

Sofa on the long wall against the red and blue art panels
Lounge side — sofa on the long wall, art panel and side table

How it was handled

StepWhat was done
1. Plan reviewThe wall run, the walkway width and the door access were measured before any piece was selected.
2. Zone sizingSofa length and dining table size were set against each other so neither zone took the walkway.
3. Palette matchingWood tone for the tables and fabric for the seating were compared side by side, not from separate sample books.
4. Three-view drawingDimensions confirmed before material was released.
5. InspectionEvery unit checked before packing, including seam alignment and table joints.
6. PackingPacked by zone, corners protected for site handling.
Dining table with red chairs and pendant lights at the window
Dining set — table, red chairs and pendant lights against the blinds

Quality gate

Frame and foam carry a three-year warranty against collapse and deformation under normal use. Every piece is inspected before packing; casegoods use E1 board with formaldehyde-tested wadding, and the reports are listed by number on the certification page.

What it means for your project

An open-plan room is decided by the gap between the two zones. Once the sofa run and the table size are set against the plan, the rest of the scheme follows — and the room keeps working after the furniture is in, not only in the photograph.

Related

Open-plan living and dining solution

Product range

Discuss an open-plan scheme

Questions on this type of order

Can the sofa be sized to the wall run?

Yes. Straight sections are adjusted by the metre; chaise sections are usually fixed. Send the wall length and the door or lift width and we confirm the largest piece that fits.

Can the dining set match the sofa fabric?

Yes. The wood tone and the fabric are compared side by side before production, and the dining chair back height is checked against the sofa back.

Can the seating and dining ship in one container?

Yes. Seating, tables and chairs are consolidated into one shipment, with a minimum of five pieces per model.

Send the plan and the scheme

Plan with both zones marked, plus the colour reference. We reply within 24 hours on working days.

Request a Quote

This note covers how the order was run. The links below lead to the product families used in this kind of fit-out, and to comparable models in the current range — they are references for specification, not a bill of materials for this project.

Product families

Comparable models: QY-S1239, QY-T7006, QY-T82201, QY-C2002.

Related: Open-plan programme · all project notes · the full product range · send a room plan.